5 Inch Touchscreen Monitor for Raspberry Pi 5 4 B 3 B+ A+, 800x480 Pixel IPS Display, 5-Point Touch Capacitive Screen, Driver-Free MIPI DSI Port

Many of my IOT solutions don't require a monitor in their final state but it is really nice to have one handy and non-combersome during development or even as a nice add on to a product where a monitor isn't an absolute necessity. The resolution is good especially for the price point. The color is pretty good but may be better if your eyesight isn't as poor as mine. The power supply is adequate and the unit worked great right out of the box. Due primarily to the reasonible cost, these are also perfect for providing a complete and super convenient system for trainees in classes I provide to young folks for free. With use of these monitors, interest can be improved serving as a great incentive to get young folks involved in what may end up being a lucrative skill in this heavily IT focused world.

Great 5inch screen for a raspberry pi. I have tested it with both the RPI3b and the Pi 4b. I have the Pi powered by a POE hat and so far has been great. Works great for klipperscreen. Great viewing angles. I can see it from across the room.

This screen works really well with the Raspberry Pi. Just plug and play in my experience. The only negative I can see is what others have mentioned - the mounting hardware on the back can break off very easily. I have lost one of these and now treat the remaining hardware very carefully. Probably better for one time mounting and leaving it alone, not for a use case where you will be mounting and unmounting the unit repeatedly. If you can live with that, or just use the included feet, these are great units.

Very pleased with this thing, so far. Worked perfectly out of the box for my Raspberry Pi 4 Model B, didn't have to fiddle with any code. Display is sharp and crisp, and it recognizes touch accurately across the whole screen with no dead spots. It comes with a small button on the top right on the PCB that controls the brightness, which has 10 settings (if you count 'Off' as the first one). The only minor complaint I have is that I wish it could go a bit brighter. In a low-light environment, it's maximum brightness is okay, but I think in brighter light environments it could do with being brighter.

This display looks great, it’s very crisp and viewing angles are superb as you’d expect from an IPS. The touch capability works great with no extra setup on my Rpi4 running bullseye. Don’t make the mistake I did and try to use it with multiple cameras connected to the CSI port on the raspberry pi. It doesn’t work with the Arducam camarray hat. It’s just an issue of crowded I2C pin usage, not a problem with this display at all.

Followed the instructions and got it working correctly. Make the raspberry pi 4b into a great mini controller attached to a piece of equipment

One cable, and you're done. I didn't have to do anything else. On first boot, it worked. Video and touchscreen work. Using 5.1V 3.5A CanaKit power supply on USB C. No power issues. Standoffs and feet were good to get it up and running while I got the case printed. Accessing the TF Card (Micro SD) with the ribbon cable in the way is annoying, but not something you should have to do once you get everything running. There is a fan header, but there are two issues. One, if you use the provided legs, they are in the way. Two, it is only 3V. My fan is 5V, which means it runs at a low speed. I put it back on the GPIO header as the amount of air it was moving was vastly different between the two. Overall, it's a good screen, and I plan to buy more for other projects that require a 5" screen.

Ordered two screens for a Project. Both worked right out of the box without question. Had one whose touch feature was not responding but found out it was my OS creating issue. Once OS issue resolved touch feature worked without issue. These screens are perfect size for my OctoPrint function of the OS and the touchscreen makes the project work great. Will be getting another one when my 4th printer is operational.

Wollte mir ein Touchdisplay für einen Raspberry Pi für meinen 3d Drucker kaufen. Dieses display ist perfekt. Einfach zu installieren, Treiber sind schnell heruntergeladen, es gibt einen Knopf mit welchem man verschiedene Helligkeitsstufen einstellen kann, touch reagiert super und die Farben sind einfach Top. Fast schon zu gut für den Preis.

Great screen, good touch, but a bit difficult to install on pi 3B+ and SKR Mini E3 V3.0 som special tricks needed. Pi board fits nicely on the back of the screen, screws included, and feet, three different length cables included. Fair price.

Couldn't be easier. Plug it in, and that's it. Perfect. Screen looks good, it's not super high res or anything but it's bright and clear. Touch works well. Power draw running rpos is about 2.7 to 3.3 watts, actually pretty good. Nothing to complain about here, this is a great little screen. Note! Raspberry-pi OS supports touchscreen but NO WAY TO RIGHT CLICK.

Bon produit, utiliser avec un raspberry pi 3 et un dac en gpio pour apporter un peu de modernité a un vieil ampli. Il ne me manque plus qu'une belle intégration....

Raspberry Pi3 A+を取り付けて使っています。タッチパネルの操作も快適にできています。 取り付けは久しぶりのリボンケーブルで一瞬戸惑いましたが、特段難しいところもなく、10分くらいで取り付けできています。 5インチを購入したので、解像度800x480は流石に今の時代厳しいなぁ、と思いつつも、簡易モニタとして使うには十分です。