VLANDLED Headlights Compatible with Toyota Tundra 2007-2013/ Sequoia 2008-2021 w/Sequential Turn Signal, w/Diamond White DRL w/LED Reflection bowl Amber Reflector Black Trim Panel

The media could not be loaded. Was nervous about the cost but I love the look and the brightness!! Plug and play took 30 minutes love it!!

Purchase with confidence! Easy to get in and look great! Took 45 minutes for the set as the instructions are not great but you match up the harnesses.

Solid product with great value compared to OEM LED assemblies from 2018+. The quality of construction appears to be excellent and fits nice and cleanly with no cheap aftermarket looking gaps.The lights come with 2 pairs of master harnesses and you use the applicable one (pair) depending on your year and trim (my truck is a 2017 SR5 without LED’s; only amber bulb DRL) PLUS a single red cable harness with 2 assembly plugs and a 2 fuse connector that you plug into the factory fuse box (if needed; see below) PLUS 2 small relay black boxes that have a 2 cable plug. Because my didn’t have the factory LED’s, I had to use that single red harness and because I had to use that harness, I was able to logically conclude which of the 2 master harness pairs I had to use. Installation otherwise was straightforward, remove grill (look up how on YouTube), old headlights (also on YouTube) and unplug all the connectors. Then match connectors between new headlight, plugs from truck and the correct master harness. Don’t forget to plug in the relay looking box plugs in that mix. It’s fairly easy to deduce what plugs into what by matching female / male connectors. If you can’t figure that part out, take it to a professional. Also, because they make them and their harness with flexibility for years and trims, there will remain unused plug(s) that don’t get plugged anywhere. Again, it’s fairly easy to figure it out. Operationally, the white LED DRL’s turn on with the truck turned on and can’t be switched off while the truck is running. The LED DRL’s do turn into orange with using the turn signals or hazards. The low and high beams also work fine. Last bit of advice, like all headlights, there are adjustment screws on the backside that allow you to properly aim the headlights. You parked your truck in front of a garage wall / wall, turn on your lights and turn the screws as needed to lower/rise the light spots you see on your wall so the 2 headlights are on the same level. You should do that exercise before mounting the grill back on as there’s no way to reach the screws with the grill. Simply install the headlights in their spots, but don’t bolt them in, making your aiming adjustments as needed and then bolt them in and put the grill back on.With the exception of not knowing how they will hold up long term with the clear plastic and condensation or leaks, for now I can definitely rate them a full 5 stars.

I purchased a set of Vland headlights in summer 2021. By summer 2023, both lenses began cracking. See attached photos of one of the headlights. Both headlights are in a similar condition. The vehicle is kept in a garage when not being driven.I tried contacting the VLand company last year but no one answered. I have waited almost 2 years for a reply to my support request, so I left an Amazon review today. It seems unacceptable that a set of $700 headlights would deteriorate in 2-3 years, but the lack of support is the primary issue I have. I will likely have to replace them this year. For frame of reference, I installed some CHEAP headlight housings in my old 2004 Honda Pilot that cost me less than $150 for the pair and 5 years later they are just fine, no cracks at all!PROS: Look good, easy to install, lower cost than some optionsCONS: Began cracking within 2 years, serious lack of supportI will be happy to update my review if the company responds.

I ordered these lights and installed them in less than two hours and they look and perform great. Definitely an improvement over a the headlights I had previously. The installation is pretty straight forward, there are twonsets of wiring harnesses and you pick the one that matches your set up. Fit and finish are great. However, I noticed that when I turned on my truck using the key there aren't any daytime running lights like I previously had. But if I stayed my truck using my remote start the daytime running lights are on. I used the link Amazon provided to contact support and went in circles. Not once did they try to answer my question but struggled to understand the fact that I purchased them through Amazon and not directly from Vland. I finally gave up and will research the problem online or live with it as is. I just hope the lights continue to perform.

First review here!! Holla!!No reviews when I purchased, but I rolled the dice. And glad I did! Mr. Toyota wanted way to much money for these OEM headlights, and these VLand versions are exactly the same! At almost half the price!They came safely packaged with a ton of molded styrofoam and plastic film over the lenses. This kit also include the two lower filler panels (another $100 if you get them from Mr. Toyota)! I'm getting them paint matched at a local body shop currently.Plug and play for my 2011 Sequoia Platinum (with factory DRL). The red ACC cable with add-a-fuse was not necessary for me, but it did change the center "hockeystick" turn signal light from constant white to constant amber while in DRL mode, which is exactly what I wanted. I did have to expand/ open up (with a file) the top outer bracket to fit over the plastic threaded insert for my vehicle, but that was very simple.I will say that I do have hyper flash with my turn signals currently...which I hope to solve soon. I'll update this review once I have a solution for it. Note: my rear turn signals are also LEDs, so I'll try going back to incandescent and see if that works.Overall a great product for a fair price.Thanks Vland!Edit:To fix the hyper flash I installed resistors (one on each side) to the beige / tan turn signal wires from the headlights (you could alternatively install the resistors to the pink / red wires from the factory wiring)I only added them to the front and kept the LED rear turn signals as they were. Resistors used: Zone Tech 50W 6Ohm LED Load Resistor

I love the style and function of these Headlights. I had an issue with one. The seller offered great customer service and replaced it with ease. Recommend this product

Nice quality